Accessories

Showing 65–80 of 86 results

  • VE.Can RJ45 terminator

    VE.Can RJ45 terminator

    The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB.

    Order Code: VE.Can RJ45 terminal

    Quick View
  • VE.Net to VE.Bus Converter

    VE.Net to VE.Bus Converter

    VE.Net stands for Victron Energy Network. It allows all VE.Net compatible devices to communicate with each other. This means that the charger, for example, can get information from the battery controller to optimize the charge current. It is possible to control and monitor all your VE.Net devices from a single VE.Net compatible control panel. This saves space and allows you to control all your devices from one place.

    Order Code: VE.Net-VE.BusConvert

    Quick View
  • Wireless sensor gateway

    Wireless sensor gateway

    Wireless AC sensors are used to measure and calculate PV Inverter current (A), voltage (V), power (W) and energy (kWh), and will show it on a Color Control GX and the VRM Portal. An installation will have one gateway and one sensor per phase. The gateway connects to the Color Control via Ethernet and is the DECT hub for the sensors.

    Order Code: Wireless Sensor G/W

    Quick View
  • CANUSB interface

    CANUSB interface

    The CANUSB interface is used to connect a VE.Can product to a computer.

    Order Code: CANUSB Interface

    Quick View
  • Battery indicator panel ( M8 eyelet / 30A ATO Fuse)

    Battery indicator panel ( M8 eyelet / 30A ATO Fuse)

    Battery Indicator Eyelet is an accessory for Blue Power IP65 and Blue Smart IP 65 chargers.

    Quick View
  • Battery indicator panel(M8 eyelet connector/30A ATO)

    Battery indicator panel(M8 eyelet connector/30A ATO)

    Battery Indicator Panel (M8 eyelet connector / 30A ATO Fuse) is an accessory of the Blue Power & Blue Smart IP65 Charger with DC connector.

    Quick View
  • Cables with M8 circular connector (for Li-ion batteries)

    Cables with M8 circular connector (for Li-ion batteries)

    M8 Connector Order Code
    Male to Female 3 pole 1 m (bag of 2) Male/Female3pole1m
    Male to Female 3 pole 2 m (bag of 2) Male/Female3pole2m
    Male to Female 3 pole 3 m (bag of 2) Male/Female3pole3m
    Male to Female 3 pole 5 m (bag of 2) Male/Female3pole5m
    Quick View
  • Fuses

    Fuses

    The Connect clamps with fuse is an accessory of the Blue Power IP65 Charger with DC connector.

    Quick View
  • Non inverting remote on-off cable

    Non inverting remote on-off cable

    Use this cable to connect the following products to the VE.Bus BMS:

    • Skylla-TG all models
    • Battery Protect models BP40i, BP60i and BP200i (all discontinued).

    The cable translates the remote on/off driver logic from the VE.Bus BMS (normally high, and open circuit in case of alarm) to the logic needed by above products: active pull down to switch off.

    pdf
    Spec Sheet

    Order Code: VE.Direct Cable

    Quick View
  • Peak Power Pack

    Peak Power Pack

    The Peak Power Pack is a complete substitute for heavy lead-acid batteries in applications where high currents occur for short time. Being primarily meant for caravan movers, it is equipped with a built-in charger allowing charging from the car electrical system during the travel with the caravan. This way the pack will be fully charged upon arrival to the camping site. If necessary, the charging is possible using the supplied adapter via a grid outlet. Charging from a solar panel is also possible.

    pdf
    Spec Sheet
    Quick View
  • Solar adapter cable MC4 male to MC3 female, length 15 cm

    Solar adapter cable MC4 male to MC3 female, length 15 cm

    Quick View
  • Solar Cable (4 mm²)

    Solar Cable (4 mm²)

    Solar Cable for 4mm² with a pre-assembled male / female MC4 (PV-ST01).

    M8 Connector :
    • Length 1 m
    • Length 3 m
    • Length 5 m
    Quick View
  • Solar connector pair MC4, 1x Male / 1x Female

    Solar connector pair MC4, 1x Male / 1x Female

    Quick View
  • Solar splitter pair MC4-Y, 1x M-2F / 1x F-2M

    Solar splitter pair MC4-Y, 1x M-2F / 1x F-2M

    Quick View
  • Victron Solar Cable (6mm²)

    Victron Solar Cable (6mm²)

    Solar Cable for 6mm² with a pre-assembled male / female MC4 (PV ST01).

    M8 Connector :
    • Length 1 m
    • Length 3 m
    • Length 5 m
    • Length 10 m
    • Length 20 m
    Quick View
  • Inverting remote on-off cable

    Inverting remote on-off cable

    Use this cable to connect the Phoenix Inverter 12/180, 24/180, 12/350 or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger that features a load output:

    • VE.Bus BMS: the Inverter will be switched off when the batteries are empty
    • BlueSolar MPPT Charger: connecting an inverter directly on the load output of a BlueSolar MPPT Charger is not possible; the inverter needs to be connected to the battery. Then use this cable to switch the inverter on and off with the load output.
    Quick View